My Rainwater Tank Is Leaking – What Does It Mean and What Happens Next?

Is a Leaking Tank a Serious Problem?

It depends entirely on where the leak is coming from. A dripping outlet fitting is a 20-minute fix. A hairline crack in a polyethylene wall can be welded closed. A failed base-to-wall joint on a concrete tank needs professional repair but is still repairable. Very few leaking rainwater tanks genuinely need to be replaced outright. The key is diagnosis.

The 5 Most Common Sources of Rainwater Tank Leaks

1. Outlet fitting failure

The outlet fitting — where your hose or plumbing pipe connects to the tank — is the most common source of leaks. It’s the point of most movement and the fitting’s rubber washer or thread seal degrades over time. Signs: water seeping or dripping directly at the connection point, corrosion around the fitting on metal tanks, visible gap between fitting and tank wall.

2. Inlet fitting failure

The inlet where roof water enters the tank can fail in similar ways, though leaks here often aren’t noticed until significant water has been lost around the tank base.

3. Overflow pipe joint

Where the overflow pipe attaches to the tank, the grommet or sealant can fail. Overflow pipes are typically under pressure only during heavy rain, so this type of leak is often intermittent and only noticed after rainfall.

4. Tank body cracking

Hairline cracks in the tank body — from UV degradation on poly tanks, ground movement on concrete tanks, or impact damage — allow a slow seep that is often first noticed as persistently damp soil on one side of the tank.

5. Base seam failure (above-ground tanks)

Some tank designs have a seam where the base meets the wall. This junction is under continuous hydrostatic pressure from the stored water. Over time, the seal at this seam can fail, producing a slow leak around the base perimeter.

How to Diagnose: Visual Inspection vs. Pressure Drop Method

Visual inspection (try this first)

  1. Dry the exterior surfaces of the tank with a cloth.
  2. Run your hand along the outside surface, starting at fittings and working across the wall from top to bottom.
  3. Look for persistent wet patches, efflorescence on concrete, rust tracks on metal tanks, or visible cracks.
  4. Check the soil immediately around the tank base for persistent dampness.

Pressure drop method (when visual inspection doesn’t reveal the source)

  1. Note the water level in the tank (mark it).
  2. Isolate the outlet so no water is leaving through normal use.
  3. Wait 24–48 hours without any refilling from the roof.
  4. Check the water level. If it has dropped beyond what evaporation accounts for, there is a leak. Recheck the exterior systematically.

When a Leak Can Be Patched vs. When Parts Need Replacing

Leak TypePatch Possible?What’s Needed
Outlet or inlet fitting dripNo — fitting replacementLicensed plumber for plumbing connections
Overflow grommet failureYes — reseal or replace grommetDIY possible in most cases
Poly body hairline crackYes — plastic weldingLicensed repairer with welding equipment
Base seam seep (poly tank)Possibly — depends on extentProfessional assessment required
Concrete through-wall crackYes — epoxy injection or membraneLicensed repairer
Concrete joint failureYes — hydraulic cement and membraneLicensed repairer

Poly Welding vs. Epoxy Patch: What’s Appropriate for Each Material

For polyethylene tanks, the only reliable repair for body cracks is plastic welding. Epoxy adhesives and sealants do not bond effectively to polyethylene — they will appear to hold initially but typically fail under the hydrostatic pressure of a full tank within months.

For concrete tanks, epoxy injection is the standard method for through-wall cracks. For concrete joint failures, hydraulic cement and waterproofing membrane is the repair sequence.

Pump-Related Leaks: Is the Leak in the Pump, Not the Tank?

Check the following before concluding the tank itself is leaking: the pump pressure vessel (a failed bladder can cause condensation and dripping around the pump body), the pump inlet connection, and the pump outlet connections. If pooling water is occurring adjacent to the pump rather than tracking back to the tank surface, isolate the pump inlet at the tank and test whether the pooling continues.

NSW Licencing: What Repair Work Requires a Licensed Plumber

In NSW, any work involving plumbing connections to a tank — replacing inlet or outlet fittings, connecting or disconnecting supply pipes — requires a licensed plumber. Repairs to the tank body itself (plastic welding, epoxy injection) can be carried out by a licensed tank repairer without a separate plumbing licence.

Frequently Asked Questions

What is the most common source of rainwater tank leaks?

The outlet fitting — where your hose or plumbing pipe connects to the tank — is the most common source of leaks. It’s the point of most movement and the fitting’s rubber washer or thread seal degrades over time.

Can I use epoxy to repair a crack in my poly water tank?

No. Epoxy adhesives and sealants do not bond effectively to polyethylene. They will appear to hold initially but typically fail under the hydrostatic pressure of a full tank within months. Plastic welding is the only reliable repair method for polyethylene body cracks.

How do I find where my rainwater tank is leaking if I can’t see it?

Use the pressure drop method: mark the water level, isolate the outlet so no water leaves through normal use, and wait 24–48 hours without any refilling from the roof. If the water level has dropped beyond what evaporation accounts for, there is a leak. Then recheck the exterior systematically.

Do I need a licensed plumber to repair my rainwater tank leak?

In NSW, any work involving plumbing connections to a tank — replacing inlet or outlet fittings, connecting or disconnecting supply pipes — requires a licensed plumber. Repairs to the tank body itself (plastic welding, epoxy injection) can be carried out by a licensed tank repairer without a separate plumbing licence.

Could pooling water near my tank actually be from the pump, not the tank?

Yes. Failed bladders inside the pressure vessel can cause condensation and dripping around the pump body, and pump inlet and outlet connections can also fail. Isolate the pump inlet at the tank and test whether the pooling continues — if it stops, the leak is in the pump assembly, not the tank.

Contact Us Today

We don't just bring tank systems back to life. We also Design and install domestic and custom water filtration systems

    Liquid Assets, Solid Savings: Choose Us for Tank Repairs!

    Using water to add value to your home

    Transform Water rainwater tank services