Can a Cracked Poly Water Tank Be Repaired? What’s Fixable, What Isn’t, and What It Costs

The First Question: Is This Tank Worth Repairing?

Most cracks in poly water tanks are repairable. But not all of them. The deciding factor in most cases is the condition of the plastic surrounding the damage. A crack in structurally sound, flexible polyethylene is a good candidate for welding. A crack in polyethylene that has become brittle and chalky from years of UV exposure is not.

What Types of Damage Can Be Repaired

Cracks in the tank wall

Hairline to moderate cracks in the tank body are the most common repair. The crack is cleaned, ground out slightly to provide a clean V-groove for the weld rod to fill, and the weld is carried out using a hot air welding gun with a polyethylene rod matched to the tank material.

Holes

Holes from impact damage are repaired using the same welding method. Larger holes may require a patch — a piece of matching polyethylene welded over the damaged area rather than a direct fill.

Fitting failures

Outlet, inlet, and overflow fittings are the most common failure points on poly tanks. The fitting is replaced, and the sealing grommet or thread connection is re-sealed. Where the fitting has pulled through the tank wall, a new fitting is installed in a fresh location and the old hole welded closed.

UV chalking (early stage)

If the tank surface has begun to chalk but the wall hasn’t cracked yet, UV-resistant exterior coatings can be applied to slow further degradation. This is maintenance, not repair — but it extends tank life and delays the point at which replacement becomes necessary.

What Makes a Tank Unrepairable

Deep structural wall thinning from UV degradation

You can detect this by pressing firmly on the tank wall — sound material flexes with some resistance; degraded material feels papery or crumbles at pressure points. If the wall has thinned to the point where it can be compressed easily, welding a crack will not restore structural integrity.

Widespread multiple cracking from UV damage

When UV degradation is systemic — cracking appearing across multiple wall sections simultaneously — the tank is at end of life. Welding individual cracks on a tank in this condition is a short-term measure at best.

Tank has deformed under load

Polyethylene tanks that have been improperly supported or exposed to ground movement can develop permanent deformation. A deformed tank wall is under ongoing stress. Welds in a stressed material are more likely to fail under hydrostatic pressure.

How Plastic Welding Works

Hot air welding

A hot air welding gun heats both the base material and a polyethylene filler rod simultaneously. The rod is fused into the prepared crack groove, bonding at a molecular level with the surrounding material as it cools. The strength of the weld depends on temperature control, rod matching, and surface preparation.

Extrusion welding

For larger cracks and patches, an extrusion welder extrudes a continuous bead of molten polyethylene rod into the joint under pressure, producing a thicker and more structurally substantial weld. This method is standard for heavier-gauge polyethylene (above 6mm wall thickness).

Why Sealants and Epoxy Patches Fail on Polyethylene

Polyethylene has a very low surface energy. That means adhesives — including epoxy resins, silicone sealants, and commercially available tank repair kits — cannot form a reliable chemical bond with it. Under the hydrostatic pressure of a full tank, the adhesive fails at the interface. Plastic welding (a fusion repair, not an adhesive repair) is the only reliable method.

Rough Cost Guide

Repair TypeTypical Cost Range (NSW)
Hairline crack weld (small)$180–$350
Moderate crack or hole repair$300–$600
Patch repair (large damaged area)$500–$900
Fitting replacement (single fitting)$120–$280
Multiple fittings plus crack repair$600–$1,200

Frequently Asked Questions

Can a cracked polyethylene water tank be repaired?

Most cracks in poly water tanks are repairable using plastic welding. The deciding factor is the condition of the plastic surrounding the damage. A crack in structurally sound, flexible polyethylene is a good candidate for welding. A crack in polyethylene that has become brittle and chalky from UV exposure is not.

Why can’t I use silicone or epoxy to fix a crack in my poly tank?

Polyethylene has a very low surface energy, which means adhesives including epoxy resins and silicone sealants cannot form a reliable chemical bond with it. Under the hydrostatic pressure of a full tank, the adhesive fails at the interface — not within the adhesive itself, but between the adhesive and the tank surface. Plastic welding is the only reliable method.

What makes a poly water tank unrepairable?

Deep structural wall thinning from UV degradation (where the wall can be compressed easily under pressure), widespread multiple cracking across several wall sections simultaneously, or permanent deformation from improper support or ground movement. In these cases, welding individual cracks is a short-term measure at best.

How long does a plastic weld repair last on a poly water tank?

A correctly executed plastic weld on a polyethylene tank in structurally sound condition will typically outlast the surrounding material — meaning the welded area is not the weak point of the tank after repair. Expect 10–20 years from a professional weld in a tank with good remaining UV resistance.

What is the difference between hot air welding and extrusion welding for tank repairs?

Hot air welding heats both the base material and a polyethylene filler rod simultaneously, fusing the rod into the prepared crack groove. Extrusion welding extrudes a continuous bead of molten polyethylene rod into the joint under pressure, producing a thicker and more structurally substantial weld. Extrusion welding is standard for heavier-gauge polyethylene above 6mm wall thickness.

Contact Us Today

We don't just bring tank systems back to life. We also Design and install domestic and custom water filtration systems

    Liquid Assets, Solid Savings: Choose Us for Tank Repairs!

    Using water to add value to your home

    Transform Water rainwater tank services