Your Rainwater Tank Before and After Summer: The NSW Homeowner’s Seasonal Checklist

Why Summer Is the Hardest Season for Your Rainwater Tank

October arrives, temperatures climb, and your rainwater system quietly moves into its most demanding three months of the year. Usage spikes. Water temperatures rise inside the tank. Algae blooms that were dormant over winter wake up. Pumps that have been ticking along fine suddenly face extended daily run times.

NSW homeowners who skip the pre-summer check often discover problems in December or January — the worst possible time, when technicians are in high demand and turnaround times blow out.

This checklist exists so that doesn’t happen to you.

Pre-Summer Checklist: 8 Things to Inspect Before October Ends

1. Inspect the tank exterior for UV and physical damage

Walk around the tank and look for surface crazing, chalking, discolouration, or any visible cracks. Poly tanks exposed to direct sunlight accumulate UV damage over time. Hairline cracks that were stable over winter can open up under the thermal expansion cycles of a hot summer. If you see chalking or deep crazing on the tank wall, get it assessed before the season begins.

2. Check the first flush diverter

Your first flush diverter captures the initial flow off your roof after rain — the dirtiest water, loaded with bird droppings, dust, and debris — and diverts it away from your tank. In summer, roof surfaces are hotter and drier between rain events, meaning the first flush carries more concentrated contamination.

Remove the cap on your first flush diverter and check that the ball float is moving freely, the chamber drains properly after use, and there’s no debris blocking the inlet. A jammed or cracked first flush diverter is one of the most common causes of tank water quality problems.

3. Look inside the tank (if accessible)

If your tank has an inspection hatch, remove the lid and take a look. You’re checking for:

  • Visible sediment layer at the base
  • Any green or brown discolouration on the walls (early algae growth)
  • Floating debris or insect entry
  • A strong earthy or musty smell

If you can see significant silt on the base or early algae growth on the walls, a professional clean before summer is worth scheduling now, not in January.

4. Test your pump pressure and flow

Run a tap connected to your rainwater system and note the pressure. Then run it for 60 seconds. If flow drops off or pressure fluctuates, your pump is working harder than it should — a sign of a partially blocked filter, a failing pressure switch, or a pump nearing the end of its service interval.

A pump that’s borderline in spring often fails outright in summer, when it’s running more frequently and the water temperature it’s pushing has increased.

5. Check your inlet screens and overflow

Inlet screens keep insects and debris out of the tank. Overflow outlets prevent the tank from over-pressuring during heavy rain. Both need to be clean and unblocked. Check screens for debris buildup, bird nesting material, and rust. Check the overflow pipe is clear at both ends.

6. Inspect tank fittings and connections

Look at where your pipes connect to the tank — inlets, outlets, and any bypass connections. Summer heat causes thermal expansion and contraction in both poly tanks and PVC pipe. Fittings that were slightly loose can work themselves into active leaks over a hot season.

7. Check your UV filter bulb age (if you have a UV filtration system)

UV bulbs degrade over time even if they appear to still be working. Most manufacturers recommend annual replacement regardless of visual appearance. If your UV bulb is more than 12 months old, replace it before summer. A degraded UV bulb does not kill bacteria at the rate you need when water temperatures are elevated and usage is high.

8. Book a professional inspection if in doubt

If you’ve found multiple issues, or you’re not comfortable assessing the system yourself, book a pre-summer service now. Technician availability in November and December books out fast. A professional inspection will assess the pump, filtration, tank condition, and plumbing connections in one visit.

Algae: What It Is, What Causes It in Summer, and How to Treat It

Algae needs three things to grow: nutrients, warmth, and light. In summer, two of those three are almost always present inside a rainwater tank. Water temperatures rise. If your tank is dark-coloured or properly fitted with a sealed lid, light exposure is minimal — but if your inlet or inspection hatch isn’t properly sealed, or if the tank material has become UV-transparent over age, you can get algae growth.

Signs of algae in your tank:

  • Green or brown tinting in your water at the tap
  • A musty or earthy smell
  • Green staining on tank walls visible through the inspection hatch
  • Slimy coating on internal surfaces

Treatment approach: Do not pour bleach directly into your drinking water tank without understanding the correct dilution and flushing protocol. NSW Health recommends chlorination as part of a controlled disinfection procedure for potable rainwater tanks. If you’ve found active algae growth, call a licensed tank technician to carry out a professional clean and disinfection rather than attempting an uncontrolled DIY treatment.

Prevention for next season:

  • Ensure all inlets are screened and light-sealed
  • Keep the inspection hatch sealed and check the gasket condition annually
  • Keep the tank in shade where possible
  • Schedule a professional clean every 2–3 years as a baseline

Bushfire and Smoke Season: What NSW Health Recommends

During bushfire events and periods of heavy smoke, your catchment roof surface accumulates ash, particulates, heavy metals, and combustion byproducts. When rain eventually arrives, your first flush diverter intercepts some of this — but not all. NSW Health recommends:

  • Do not drink rainwater during or immediately after a fire or significant smoke event. Switch to an alternative potable water source.
  • After the fire or smoke event has passed, clean the roof catchment area before resuming rainwater collection.
  • Pump out and test the tank water before resuming use for drinking, cooking, or food preparation.
  • Ash and combustion particulates can contain polycyclic aromatic hydrocarbons (PAHs) that are not removed by standard sediment filtration — UV or activated carbon filtration is required.

Summer Pump Load: Warning Signs Before It Becomes a Problem

Signs your pump is under excessive load:

  • Pump runs for longer than usual cycles
  • Reduced flow rate at taps and garden hose connections
  • Pump kicks on more frequently than you expect
  • Pump makes clicking or stuttering sounds at startup
  • Pressure vessel feels abnormally hot to touch

If you notice any of these signs before summer, get the pump serviced. A pre-emptive service is significantly cheaper than an emergency callout in January.

Post-Summer Checklist: What to Check After the Heat

  • Inspect for any UV-related cracking that may have developed over the hot months
  • Check overflow outlet for summer debris accumulation
  • Reassess pump performance after three months of elevated load
  • If there was any fire or smoke event near your catchment, have the tank water tested before resuming drinking use
  • Book a professional clean if more than two years have elapsed since the last one

Frequently Asked Questions

Why is summer the worst time to discover a rainwater tank problem?

High usage, bushfire smoke contamination, algae growth in warmer water, and increased pump load all peak between October and March. Technician availability also books out fast in December and January, meaning turnaround times blow out when you need help most.

What does a jammed first flush diverter cause?

A jammed or cracked first flush diverter is one of the most common causes of tank water quality problems. It means the dirtiest roof runoff — loaded with bird droppings, dust, and debris — enters your tank instead of being diverted away.

What are the signs of algae in a rainwater tank?

Green or brown tinting in your water at the tap, a musty or earthy smell, green staining on tank walls visible through the inspection hatch, and a slimy coating on internal surfaces.

Can I treat algae in my rainwater tank with bleach?

Do not pour bleach directly into your drinking water tank without understanding the correct dilution and flushing protocol. If you’ve found active algae growth, call a licensed tank technician to carry out a professional clean and disinfection rather than attempting an uncontrolled DIY treatment.

What should I do if there was a bushfire or smoke event near my catchment area?

Do not drink rainwater during or immediately after a fire or significant smoke event. After the event passes, clean the roof catchment area before resuming collection, and pump out and test the tank water before resuming use for drinking, cooking, or food preparation.

What are the warning signs that my rainwater pump is under excessive load?

The pump runs for longer than usual cycles, reduced flow rate at taps and garden hose connections, the pump kicks on more frequently than expected, clicking or stuttering sounds at startup, and the pressure vessel feels abnormally hot to touch.

Contact Us Today

We don't just bring tank systems back to life. We also Design and install domestic and custom water filtration systems

    Liquid Assets, Solid Savings: Choose Us for Tank Repairs!

    Using water to add value to your home

    Transform Water rainwater tank services