Why Concrete Water Tanks Crack
Concrete has been used for rainwater storage in NSW for over a century. A well-built concrete tank, properly maintained, can last 50 years or more. But concrete is not inert — it moves, reacts with water, and deteriorates through specific mechanisms that are worth understanding if you own one.
Mechanism 1: Ground movement
Reactive clay soils are common across NSW, particularly in western and south-western Sydney. These soils expand and contract with seasonal moisture changes. A concrete tank sitting in reactive clay experiences differential pressure across its base and walls as the soil moves. This produces cracking — usually horizontal cracking across the lower third of the tank wall, or diagonal cracking at corners.
Mechanism 2: Poor original mix design or curing
Older concrete tanks — particularly those built prior to the 1990s — were often constructed with lower cement-to-aggregate ratios and minimal reinforcement. A thin, under-reinforced tank wall is susceptible to cracking from relatively minor ground movement or settlement.
Mechanism 3: Carbonation
Over time, concrete reacts with atmospheric CO2 in a process called carbonation. This lowers the pH of the concrete, which compromises the protective passivation layer around steel reinforcement. Once that layer is gone, embedded steel rusts, expands, and causes the concrete cover to spall. Carbonation-related spalling is typically visible as brown rust staining on the tank exterior accompanied by chunks of concrete falling away from the surface.
The 3 Types of Concrete Tank Cracking
Type 1: Surface cracking (crazing or shrinkage cracks)
Fine network cracking across the surface, often called crazing. Usually cosmetic in older tanks. Does not typically represent a structural problem, but can allow water ingress that accelerates carbonation.
Type 2: Through-wall structural cracking
Cracks that run through the full thickness of the wall. These actively leak. The key sign is water seeping through the exterior face of the tank. Through-wall cracks require active repair to restore water-tightness.
Type 3: Joint failure
The junction between the base slab and the wall is a common failure point, particularly in tanks where the base and walls were poured separately. Water pressure from inside the tank pushes against this joint, and over time the seal fails. Joint failure produces a consistent seeping leak at the base of the interior wall.
Why Concrete Tanks Leach Lime
Lime leaching — white mineral deposits on the exterior surface, or a slightly milky appearance in the water — occurs as calcium hydroxide leaches from the concrete as water passes through micro-voids. For drinking water, it raises the pH and can affect taste. An internal waterproofing membrane is the long-term solution.
Repair Methods: Which Scenario Each Suits
Epoxy injection
Epoxy injection is used for active through-wall cracks where structural integrity is still intact. A two-part epoxy resin is injected under low pressure through ports drilled along the crack. It is appropriate when the crack is isolated, the concrete surrounding it is structurally sound, and the crack is not actively moving.
Hydraulic cement
Hydraulic cement sets in the presence of water and is used to stop active water seeping through cracks or joints in real time. It is typically used as a first step before a surface-applied waterproofing membrane.
Full interior reline (waterproofing membrane)
A full interior reline involves applying a cementitious or epoxy waterproofing membrane to all internal surfaces. This creates a continuous barrier between the stored water and the concrete substrate, preventing both water ingress and lime leaching. Products used must comply with AS/NZS 4020 for drinking water contact.
Realistic Lifespan After Repair vs. After Reline
| Repair Type | Expected Additional Lifespan | Conditions |
|---|---|---|
| Epoxy crack injection | 10–20+ years | Crack must be structurally stable; no further ground movement |
| Hydraulic cement joint repair | 5–15 years | May need reapplication if movement continues |
| Full interior reline | 20–30+ years | Dependent on concrete substrate integrity at time of reline |
Frequently Asked Questions
Why do concrete water tanks crack?
Concrete water tanks crack for three main reasons: ground movement (particularly in reactive clay soils common across NSW), poor original mix design or curing in older tanks, and age-related carbonation that compromises reinforcement and causes the concrete cover to spall.
What is the difference between a surface crack and a through-wall crack?
Surface cracking (crazing or shrinkage cracks) is usually cosmetic and doesn’t represent a structural problem, though it can allow water ingress that accelerates carbonation. Through-wall structural cracks run through the full thickness of the wall and actively leak — water seeps through the exterior face of the tank and requires active repair.
When should I reline a concrete water tank instead of repairing it?
A full interior reline is appropriate when there are multiple cracks, the concrete surface has widespread surface deterioration, the tank has reached the end of its effective structural life but still has sound walls, or the owner wants a long-term solution that also addresses water quality and lime leaching concerns. A reline is not a substitute for structural repair — a tank with active structural movement needs structural assessment first.
Are all concrete repair products safe for drinking water tanks?
No. Epoxy resins and waterproofing membranes used inside potable water tanks must comply with AS/NZS 4020 (Testing of products for use in contact with drinking water). Using non-compliant products inside a drinking water tank can leach plasticisers and solvents into your stored water. Always confirm compliance when getting quotes.
Why does water from my concrete tank look milky or have a strange taste?
This is likely lime leaching — calcium hydroxide leaching from the concrete as water passes through micro-voids in the structure. For drinking water use, it raises the pH and can affect taste. The long-term solution is an internal waterproofing membrane that creates a barrier between the stored water and the concrete substrate.




